AC WORKS® Library

User Manual: 20 or 30 Ampere Locking Plugs and Connectors

Posted by Stephanie Junek on Jan 19, 2018

1. CABLE: Provide a cable of applicable ampacity, service and temperature rating suitable for the conditions of use and location. The plugs and connectors are designed for use with 3, 4 or 5 conductor cables with a diameter from .375’’ to 1.56” (12/3 SJ through 8/5 S). 2. CORD CLAMP PREP: Gray colored cord clamp inserts preinstalled for use with .550” to .875” cable diameter. If you need other sizes, please contact us. 3. CABLE PREP: Remove out jacket 2” and strip each individual conductor 5/8” as shown in Figure 1 Below. Make sure the wire is clean and bright...

0 comment
Tags: 10-50 plug, 20 AMP, 20 amp connector, 20 Amp locking plugs and connectors, 20 amps locking, 2018, 30 Amp, 30 amp connector, 30 amp locking, 30 amp locking plug and connector, AC Connectors, AC Works, AC Works brand, Assembly, connectors, Customer Service, Different Connectors, Easy Assembly, Emergency Power, Emergency Power System, L14-20, L14-30, L15-20, L15-30, L16-20, L16-30, L21-20, L21-30, L5-20, L5-30, L6-20, L6-30, NEMA, NEMA pin configuration, Plug, Power, Power Solutions, Receptacle, Residential Power, Residential Use, Safety, Safety Tips, Technical

Download: Residential Product Sheet

Posted by Stephanie Junek on Jan 05, 2018

Download the AC WORKS® Residential Power product sell sheet here.

User Manual: 15, 20 and 30 Amp Straight-Blade or Locking Inlet

Posted by Stephanie Junek on Dec 13, 2017

1. CABLE: Provide a cable of applicable ampacity, service and temperature rating suitable for the conditions of use and location. The plugs and connectors are designed for use with 3, 4, or 5 conductor cables with a diameter from .375’’ to 1.156’’ (12/3 SJ through 8/5 S). 2. CORD CLAMP PREP: Gray colored cord clamp inserts preinstalled for use with .550’’ to .875’’ cable diameter. For other sizes: A. Loosen and remove the cord clamp assembly from the housing. B. Remove the gray colored cord clamps from the cord clamp assembly. C. Replace with an appropriately supplied cord clamp insert:...

User Manual: 30 Amp Inlet Box

Posted by Stephanie Junek on Nov 02, 2017

IMPORTANT! Installation of your AC WORKS® brand temporary power inlet box and associated wiring must be performed by a licensed electrician in compliance with all applicable codes. Mount the temporary power inlet box in a suitable location using the holes provided in your AC WORKS® brand inlet box packaging. All wiring methods and materials must conform to NEMA practices. Route the conduit or cable through one of the provided knockouts in the inlet box. Route the cable or conduit to the junction box. All conductors are to be at least 10 AWG but not exceeding 8 AWG. Include a ground wire of the...

AC Connectors and AC WORKS® Limited Warranty

Posted by Stephanie Junek on Oct 27, 2017

AC WORKS® brand products, excluding DIY products, are protected by a 5-year limited warranty. The DIY products are protected by a 1-year limited warranty. This limited warranty covers defects in product material, craftsmanship, and performance that occur under normal use of the product. This limited warranty does not cover any damage or malfunction directly or indirectly caused by, or due to, or resulting from, normal wear or deterioration, abuse, misuse, negligence, accident, lack of or improper use, maintenance, storage or transport including, but not limited to the following: Failure to follow instructions and user manuals, maintenance and warnings published with the...